Ameristar, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, Ameristar products meet top standards in residential heating and cooling. Whether upgrading or installing new, Ameristar provides advanced solutions to keep your home comfortable year-round. What's Included: Ameristar A5HP4024A Condenser: A budget-friendly, reliable single-stage heat pump built to Trane Technologies quality standards, delivering up to 14.3 SEER2 / 7.5 HSPF2 efficiency with R-454B refrigerant for both cooling and cold-climate heating in one outdoor unit. Ameristar A801X040AM3S Backup Furnace: An entry-level, dependable 80% AFUE gas furnace built to Trane Technologies quality standards, featuring a constant-torque ECM blower and multi-position (upflow/downflow/horizontal) cabinet design for straightforward installation. 5TXC Cased Aluminum Evaporator Coil 5TXCA002AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 2 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model A5HP4024A Condenser Stages Single Furnace Model A801X040AM3S Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCA002AS Heat Source Gas AHRI 215485836 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$9,414.57
Ameristar, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, Ameristar products meet top standards in residential heating and cooling. Whether upgrading or installing new, Ameristar provides advanced solutions to keep your home comfortable year-round. What's Included: Ameristar A5HP4018A Condenser: A budget-friendly, reliable single-stage heat pump built to Trane Technologies quality standards, delivering up to 14.3 SEER2 / 7.5 HSPF2 efficiency with R-454B refrigerant for both cooling and cold-climate heating in one outdoor unit. Ameristar A801X040AM3S Backup Furnace: An entry-level, dependable 80% AFUE gas furnace built to Trane Technologies quality standards, featuring a constant-torque ECM blower and multi-position (upflow/downflow/horizontal) cabinet design for straightforward installation. 5TXC Cased Aluminum Evaporator Coil 5TXCB003AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 1.5 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model A5HP4018A Condenser Stages Single Furnace Model A801X040AM3S Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB003AS Heat Source Gas AHRI 215485716 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$9,216.53
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6060A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1C100M5PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCC009AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 5 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6060A Condenser Stages Single Furnace Model S8X1C100M5PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCC009AS Heat Source Gas AHRI 218109425 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$13,337.82
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6048A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1C080M5PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCC009AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 4 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6048A Condenser Stages Single Furnace Model S8X1C080M5PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCC009AS Heat Source Gas AHRI 218109101 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$12,801.64
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6042A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1B080M4PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCB006AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 3.5 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6042A Condenser Stages Single Furnace Model S8X1B080M4PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB006AS Heat Source Gas AHRI 218108577 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$12,358.87
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6036A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1B060M4PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCB006AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 3 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6036A Condenser Stages Single Furnace Model S8X1B060M4PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB006AS Heat Source Gas AHRI 218108011 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$12,052.49
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6030A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1B060M4PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCB003AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 2.5 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6030A Condenser Stages Single Furnace Model S8X1B060M4PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB003AS Heat Source Gas AHRI 218395349 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$11,643.34
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6024A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8X1A040M3PS Backup Furnace: The American Standard S8X1 is the wider-cabinet counterpart to the S8B1, an 80% AFUE single-stage gas furnace with aluminized-steel heat exchanger and ECM blower, built in a 21 in. wide cabinet for higher airflow / larger duct systems at the same BTU input range (40,000-100,000 BTU). Cabinet width (17.5 in for S8B1 vs 21 in for S8X1) is the primary distinguishing factor between the two series, not efficiency or staging. 5TXC Cased Aluminum Evaporator Coil 5TXCB003AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 2 Ton Bundle Cooling Efficiency (SEER2) 15.2 SEER2 Condenser Model 5A6H6024A Condenser Stages Single Furnace Model S8X1A040M3PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB003AS Heat Source Gas AHRI 218106535 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$11,361.24
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H6018A Condenser: Positioned as the step-up 'Silver 15' single-stage heat pump above the 5A6H4, offering a wider efficiency range up to 15.2-16 SEER2 and 7.5-8.1 HSPF2 on R-454B refrigerant across 1.5-5 ton capacities. NOTE: could not verify the exact model prefix '5A6H6' in any official American Standard documentation; the verified official Silver 15 heat pump prefix is 5A6H5 -- please confirm the model numbering with your supplier before publishing. American Standard S8B1B040M2PS Backup Furnace: The American Standard S8B1 is an 80% AFUE single-stage gas furnace with an aluminized-steel tubular heat exchanger, constant-torque/ECM blower motor, and hot-surface ignition, offered in upflow/downflow/horizontal configurations from 40,000 to 120,000 BTU input. It uses the standard 17.5 in. wide cabinet. 5TXC Cased Aluminum Evaporator Coil 5TXCA002AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 1.5 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model 5A6H6018A Condenser Stages Single Furnace Model S8B1B040M2PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCA002AS Heat Source Gas AHRI 218112855 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$10,705.50
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H4060A Condenser: The American Standard 5A6H4 is a single-stage Silver 14 split-system heat pump built around a SpineFin outdoor coil and a durable scroll compressor, delivering up to 15.2 SEER2 cooling and 8.1 HSPF2 heating on low-GWP R-454B refrigerant, available in 1.5-5 ton (018-060) capacities. American Standard S8B1D120M5PS Backup Furnace: The American Standard S8B1 is an 80% AFUE single-stage gas furnace with an aluminized-steel tubular heat exchanger, constant-torque/ECM blower motor, and hot-surface ignition, offered in upflow/downflow/horizontal configurations from 40,000 to 120,000 BTU input. It uses the standard 17.5 in. wide cabinet. 5TXC Cased Aluminum Evaporator Coil 5TXCD010AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 5 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model 5A6H4060A Condenser Stages Single Furnace Model S8B1D120M5PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCD010AS Heat Source Gas AHRI 215485634 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$12,386.89
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H4048A Condenser: The American Standard 5A6H4 is a single-stage Silver 14 split-system heat pump built around a SpineFin outdoor coil and a durable scroll compressor, delivering up to 15.2 SEER2 cooling and 8.1 HSPF2 heating on low-GWP R-454B refrigerant, available in 1.5-5 ton (018-060) capacities. American Standard S8B1C080M5PS Backup Furnace: The American Standard S8B1 is an 80% AFUE single-stage gas furnace with an aluminized-steel tubular heat exchanger, constant-torque/ECM blower motor, and hot-surface ignition, offered in upflow/downflow/horizontal configurations from 40,000 to 120,000 BTU input. It uses the standard 17.5 in. wide cabinet. 5TXC Cased Aluminum Evaporator Coil 5TXCC007AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 4 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model 5A6H4048A Condenser Stages Single Furnace Model S8B1C080M5PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCC007AS Heat Source Gas AHRI 215485244 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$11,624.66
American Standard, offered by McKinney HVAC, is a trusted name in home comfort, delivering high-performance HVAC systems that combine efficiency, reliability, and innovation. Focused on energy savings and durability, American Standard products meet top standards in residential heating and cooling. Whether upgrading or installing new, American Standard provides advanced solutions to keep your home comfortable year-round. What's Included: American Standard 5A6H4042A Condenser: The American Standard 5A6H4 is a single-stage Silver 14 split-system heat pump built around a SpineFin outdoor coil and a durable scroll compressor, delivering up to 15.2 SEER2 cooling and 8.1 HSPF2 heating on low-GWP R-454B refrigerant, available in 1.5-5 ton (018-060) capacities. American Standard S8B1B060M4PS Backup Furnace: The American Standard S8B1 is an 80% AFUE single-stage gas furnace with an aluminized-steel tubular heat exchanger, constant-torque/ECM blower motor, and hot-surface ignition, offered in upflow/downflow/horizontal configurations from 40,000 to 120,000 BTU input. It uses the standard 17.5 in. wide cabinet. 5TXC Cased Aluminum Evaporator Coil 5TXCB006AS Evaporator Coil: The American Standard 5TXC is an aluminum cased multi-position (upflow/downflow/horizontal) evaporator coil engineered for use with Silver-series condensers and heat pumps, sized 1.5-5 ton, compatible with R-454B refrigerant systems. Includes licensed and insured HVAC installation by professionals, along with the Install Kit for a complete setup. Professional Installation: Removal & haul-off of existing equipment Installation of new equipment and all included parts Refrigerant line connection, evacuation & charge to OEM spec Full system start-up, airflow check & operational testing Permit pulled and permit fees paid with the local jurisdiction Final inspection and job-site clean-up Performed by a licensed, insured HVAC contractor Dual Fuel Kit (Heat Pump Condenser & Coil + Backup Furnace) Electrical & mounting disconnect, A/C whip, condenser pad Refrigerant line filter drier, locking caps, ArmaFlex insulation Gas line gas flex hose, gas pipe fittings (nipples, unions, shut-off, drip leg) Venting flue pipe & elbow set for furnace exhaust Drainage & PVC P-trap, full PVC fittings kit (couplings, elbows, tee, adapters) Not Included: This listing covers the equipment and standard installation scope above. The following items are not included unless specifically listed on your written invoice or estimate: Electrical panel upgrades or new breakers beyond the conventional disconnect Ductwork modifications, repairs, replacement, or new runs New refrigerant line set (existing line set is reused when in good condition) Condenser pad re-pour, raised platform, or hurricane tie-downs (standard composite pad is included) Condenser relocation to a new exterior position Crane or rooftop rigging for difficult equipment access Gas line extension, re-routing, or new gas line installation Condensate drain line rework beyond the immediate connection at the unit Thermostat upgrades (standard thermostat reuse only) Asbestos abatement, mold remediation, or hazardous material handling Carpentry, drywall, paint, or flooring repair after installation If any of the above are needed for your home, your technician will note it on your estimate before work begins. SPECIFICATIONS Bundle Size/Tonnage 3.5 Ton Bundle Cooling Efficiency (SEER2) 14.3 SEER2 Condenser Model 5A6H4042A Condenser Stages Single Furnace Model S8B1B060M4PS Furnace Stages Single-Stage Furnace Efficiency 80% Coil Model 5TXCB006AS Heat Source Gas AHRI 215484664 Refrigerant R-454B Warranty 10 Year Parts, 10 Year Compressor (When Registered with OEM) RESOURCES Condenser Furnace Coil LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY SPEC SHEET SPEC SHEET SPEC SHEET
$11,292.12
